|
Title: 2.4 doesn't see my PCI-e NIC Post by: TheEricHarris on Thursday 05 August 2010, 06:26:48 am I have a Dell R210 with two onboard NICs that are detectetd fine. I have a Rosewill RC-411 PCI-e NIC that is not being detected by ENDIAN.
It did detect it at one point. root@scfw1:~ # cat /var/log/messages | grep eth2 Aug 4 08:46:00 efw-community kernel: [ 5.034486] eth2: Identified chip type is 'RTL8168D/8111D'. Aug 4 08:46:00 efw-community kernel: [ 5.034489] eth2: RTL8168B/8111B at 0xf8844000, 00:0a:cd:1a:d5:ce, IRQ 220 ifconfig shows: root@scfw1:~ # ifconfig br0 Link encap:Ethernet HWaddr B8:AC:6F:87:45:52 inet addr:172.30.100.144 Bcast:172.30.100.255 Mask:255.255.255.0 inet6 addr: fe80::baac:6fff:fe87:4552/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:785 errors:0 dropped:0 overruns:0 frame:0 TX packets:880 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:50155 (48.9 KiB) TX bytes:577730 (564.1 KiB) eth0 Link encap:Ethernet HWaddr B8:AC:6F:87:45:52 inet6 addr: fe80::baac:6fff:fe87:4552/64 Scope:Link UP BROADCAST RUNNING PROMISC MULTICAST MTU:1500 Metric:1 RX packets:785 errors:0 dropped:0 overruns:0 frame:0 TX packets:970 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:66761 (65.1 KiB) TX bytes:586206 (572.4 KiB) Interrupt:16 Memory:da000000-da012700 eth1 Link encap:Ethernet HWaddr B8:AC:6F:87:45:53 inet addr:192.168.157.175 Bcast:192.168.157.255 Mask:255.255.255.0 inet6 addr: fe80::baac:6fff:fe87:4553/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:321 errors:0 dropped:0 overruns:0 frame:0 TX packets:43 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:47393 (46.2 KiB) TX bytes:3987 (3.8 KiB) Interrupt:17 Memory:dc000000-dc012700 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:507 errors:0 dropped:0 overruns:0 frame:0 TX packets:507 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:89894 (87.7 KiB) TX bytes:89894 (87.7 KiB) Any suggestions on what I can try? Title: Re: 2.4 doesn't see my PCI-e NIC Post by: TheEricHarris on Thursday 05 August 2010, 09:53:35 am It shows in lspci -v on first boot:
01:00.0 Class ffff: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gi gabit Ethernet controller (rev 03) Flags: fast devsel, IRQ 255 I/O ports at <unassigned> [disabled] Memory at <unassigned> (64-bit, non-prefetchable) [disabled] Expansion ROM at <ignored> [disabled by cmd] Capabilities: [fc] <chain broken> WTF. Is this an IRQ conflict? Title: Re: 2.4 doesn't see my PCI-e NIC Post by: danielcsgomes on Friday 13 August 2010, 04:00:19 am You have to install drivers manually, you have to download the EFW Community 2.4 devel SRMPS to install the packages you need to install your nic drivers.
I have to do the same for my Atheros AR8131 onboard nic. http://efwsupport.com/index.php?topic=610.msg1697 See that topic but remember that you need the 2.4 version of devel SRMPS. Title: Re: 2.4 doesn't see my PCI-e NIC Post by: TheEricHarris on Saturday 14 August 2010, 12:29:05 am Here's an update.
I bought a HP NC110T Pci express Gigabit NIC. It works just fine with 2.4 on a Dell PowerEdge R210 (3 NICs total). |