Welcome, Guest. Please login or register.
Did you miss your activation email?
Friday 06 December 2024, 03:18:05 am

Login with username, password and session length

Get the new Updates directly from Endian  HERE
14261 Posts in 4377 Topics by 6517 Members
Latest Member: Sandro
Search:     Advanced search
+  EFW Support
|-+  Support
| |-+  EFW SMTP, HTTP, SIP, FTP Proxy Support
| | |-+  Problem with http proxy configuration
0 Members and 4 Guests are viewing this topic. « previous next »
Pages: [1] Go Down Print
Author Topic: Problem with http proxy configuration  (Read 15882 times)
sunnet
Jr. Member
*
Offline Offline

Posts: 3


« on: Thursday 01 April 2010, 04:17:59 am »

I have an Endian Firewall 2.2 which works very well. I would like to upgrade to version 2.3 and am trying to configure it but when I open the browser, it not asks me for logon credentials. I created groups and users, but nothing, it open directly the page that shows me that the site is blocked. Where can I find informafioni for such a configuration, or is there someone who can help me?
Logged
whoiam55
Full Member
***
Offline Offline

Posts: 71



WWW
« Reply #1 on: Thursday 01 April 2010, 05:55:47 am »

If it say that site is blocked implies that you have selected a category in the content filter profile which clocking the site you want to open. Try selecting a few category to rule out the problematic one Wink

cheers!
Logged

सत्यमेव जयते!
sunnet
Jr. Member
*
Offline Offline

Posts: 3


« Reply #2 on: Thursday 01 April 2010, 07:01:32 pm »

Thank you, but my primary problem is that the EFW not asks me the logon for the browser.
Logged
whoiam55
Full Member
***
Offline Offline

Posts: 71



WWW
« Reply #3 on: Thursday 01 April 2010, 09:07:16 pm »

You need to enable authentication but you can't use transparent mode.
Logged

सत्यमेव जयते!
gyp_the_cat
Full Member
***
Offline Offline

Posts: 81



WWW
« Reply #4 on: Thursday 01 April 2010, 09:08:22 pm »

Hi Sunnet,

If I understand correctly, try:

Proxy - HTTP - Configuration - Authencation Required



It sounds like it could be on disabled at the moment allowing all traffic through.

Gyp
Logged
koukobin
Full Member
***
Offline Offline

Posts: 24


« Reply #5 on: Friday 02 April 2010, 02:33:47 pm »

I had the same problem once in a new endian installation.

I had a message that i am not authenticated but i was using transparent proxy that does not need authentication.

I realized that the problem was with the havp service (check the log files for havp).

Specifically, havp couldn't find the files whitelist and blacklist in the folder /etc/havp .

For a strange reason these files were not there (the links for these file because the original files are located in the folder /var/efw/havp).

Havp cannot work without them even if they are empty. The service needs them to start (see the conf file of havp)

I created them manually (touch /etc/havp/whitelist) and set the owner as nobody (chown nobody:nobody /etc/havp/whitelist)

and then i restarted the havp service (/etc/init.d/havp restart). Finally i restarted the squid and the problem was solved.

I hope this will help.
Logged
Pages: [1] Go Up Print 
« previous next »
Jump to:  

Page created in 0.109 seconds with 18 queries.
Powered by SMF 1.1 RC2 | SMF © 2001-2005, Lewis Media Design by 7dana.com