Welcome, Guest. Please login or register.
Did you miss your activation email?
Monday 09 December 2024, 08:46:39 pm

Login with username, password and session length

The Latest Endian Firewall is now available for download HERE
14261 Posts in 4377 Topics by 6517 Members
Latest Member: Sandro
Search:     Advanced search
+  EFW Support
|-+  Support
| |-+  Installation Support
| | |-+  NIC BCM 5717 not work on endian2.5.2
0 Members and 0 Guests are viewing this topic. « previous next »
Pages: [1] Go Down Print
Author Topic: NIC BCM 5717 not work on endian2.5.2  (Read 20570 times)
manu6600
Jr. Member
*
Offline Offline

Posts: 2


« on: Thursday 07 November 2013, 02:37:59 pm »

I have installed Endian 2.5.2 on HP server, NIC card 5717. After successfully installation, i can get through web interface. then, I try to ping the address but can't be reached.  I test the cards from console by ping to itself, it was replied but it can reach other devices on the networks.

Is that NIC card support Endian?

Thanks for your help.
Logged
manu6600
Jr. Member
*
Offline Offline

Posts: 2


« Reply #1 on: Thursday 07 November 2013, 02:52:02 pm »

Screen shot of NIC BCM 5717

img20.imageshack.us/img20/8545/un35.jpg
Logged
hadexx
Full Member
***
Offline Offline

Posts: 10


« Reply #2 on: Thursday 06 February 2014, 05:42:58 am »

i have the same problem ...

you maybe try

dowload the RPM paket of drivers

search in google.com

Controladores, software y firmware para Adaptador HP Ethernet 1 Gb de 2 puertos 330i


ant try to install

copy to USB

smart install "your route "

if the KEY of RPM  dont work try

smart config -–set rpm-check-signatures=false
or
smart config –set rpm-check-signatures=False

install
 and reverse the change

smart config –set rpm-check-signatures=true

reboot and try of work



Logged
hadexx
Full Member
***
Offline Offline

Posts: 10


« Reply #3 on: Thursday 06 February 2014, 06:37:38 am »

try the instruccions to kieronrob

As luck would have it as I post for help I find a solution!

This is how I solved it:

1. Connected an ASIX USB NIC and configured it as GREEN
2. Connected a Conexant USB ADSL Modem
3. Connect to the Endian and enable SSH
4. Connect via WinSCP
5. Edit /etc/modprobe.conf and add the following line at the end: install tg3 /sbin/modprobe broadcom; /sbin/modprobe --ignore-install tg3
6. Save
7. Edit /etc/modprobe.d/modprobe.conf.dist and add the following lines at the end: install tg3 /sbin/modprobe broadcom; /sbin/modprobe --ignore-install tg3;
install skfp /sbin/modprobe marvell; /sbin/modprobe --ignore-install skfp. Note that these are two seperate lines!
8. Save
9. Reboot
10. Go into the "Network Configuration" menu on the dashboard and the NICs will be available to configure as you wish.
11. Remove the USB NIC if you wish.

I have tried this and it works, the cards I have are listed as follows in the lspci output:

01:00.0 Ethernet controller: Broadcom Corporation NetLink BCM57788 Gigabit Ethernet PCIe (rev 01)

lspci -n show it as the following:

01:00.0 0200: 14e4:1691 (rev 01)

If it stops or gives trouble, I will update.

I do not know if these changes will survive and update from Endian, but seeing as they are very few and far between, I suspect it will not be a problem. If they do update the kernel at some point, these hacks should not be necessary and the NICs work fine with newer kernel distros.

I hope someone finds this helpful!


thk

kieronrob
Logged
Pages: [1] Go Up Print 
« previous next »
Jump to:  

Page created in 0.063 seconds with 19 queries.
Powered by SMF 1.1 RC2 | SMF © 2001-2005, Lewis Media Design by 7dana.com