efw-upgrade EFW 2.4?

[Guest]

[endian-christian]

ok, so basically something already went wrong while performing the upgrade from 2.2 to 2.3... :-/
efw-base is definitely from the 2.2 release which is why you see the 2.2 at the bottom of the page...

Until I double checked the version, I thought the upgrade went fine.  However, as you say some went wrong.  I would guess at this point a clean install of 2.3 should be done after doing a backup.  Once 2.3 is installed, restore backup and all should be well?
Then perhaps do an upgrade to 2.4.

I'd recommend you create a backup of your settings, install version 2.4 and then import your backup.
You can download a new ISO I created here (second link contains the MD5 checksum):
http://public.endian.com/christian/EFW-COMMUNITY-2.4-201005280528.iso
http://public.endian.com/christian/EFW-COMMUNITY-2.4-201005280528.iso-md5sum.txt

The image will be  until tomorrow some time in the afternoon (CET).

Regards,
Christian

[arminf]

Downloaded installed
- imported backup

Result:
NIC Ports where mixed up after import
CPU 100% most of the time
InterZone FW traffic is still scanned with SNORT if option set to "allow" instead of "allow with IPS"

Lanner FW 7530
Atom N270 1.6 Ghz ht
2 GB RAM
8 GB CF card
4* Intel GigaPorts
2*Intel GigaPorts

--Update
reconfig SNORT
reconfig Network settings (red, blue, green)
go through most of settings and save them.
- reboot

Mine looks good now!

[thanit]

Hi Christian.
I  cannot enable IPSec VPN because there is no Save button present.
Please help me too.

Regards.
Thanit

[thanit]

ok, so basically something already went wrong while performing the upgrade from 2.2 to 2.3... :-/
efw-base is definitely from the 2.2 release which is why you see the 2.2 at the bottom of the page...

Until I double checked the version, I thought the upgrade went fine.  However, as you say some went wrong.  I would guess at this point a clean install of 2.3 should be done after doing a backup.  Once 2.3 is installed, restore backup and all should be well?
Then perhaps do an upgrade to 2.4.

I'd recommend you create a backup of your settings, install version 2.4 and then import your backup.
You can download a new ISO I created here (second link contains the MD5 checksum):

The image will be  until tomorrow some time in the afternoon (CET).

Regards,
Christian

The "EFW-COMMUNITY-2.4-201005280528.iso", Is it working for enable IPSec VPN Save button problem or not ?

Regards.
Thanit.

[ad.aimm]

thanit

i haven't check ipsec but there are severals bugs with other translation than english and FF. so use, english language as default and IE.

regards,

ad.

[thanit]

ad.aimm

The "EFW-COMMUNITY-2.4-201005280528.iso". It works for IPsec VPN 

Regards
Thanit

[maguilera72]

Hi all,

To it simple, here is a small procedure to upgrade from a 2.3 install and obtain a 2.4.

it worked for me, when i has the USB issues.

Thanks again Endian, your solutions rocks !

[itmltd]

Hello,

Any news on Vmware SCSI controller support ?

Thanks,
Serdar

[ENatter]

Any news on Vmware SCSI controller support ?

Hello!

Looks like. It install's now also on VM with SCSI-Harddisk.

[itmltd]

Thanks ENatter,

Upgrade from 2.3 to 2.4 was smooth on vmware. Looks like SCSI controller issues are fixed. Everything is OK now.

Thanks Endian for a great product.