EFW Support
Welcome,
Guest
. Please
login
or
register
.
Did you miss your
activation email?
Thursday 26 December 2024, 07:19:09 am
1 Hour
1 Day
1 Week
1 Month
Forever
Login with username, password and session length
Download the latest community FREE version
HERE
14262
Posts in
4377
Topics by
6517
Members
Latest Member:
Sandro
Search:
Advanced search
EFW Support
Support
General Support
multi WAN and VLAN questions
0 Members and 1 Guest are viewing this topic.
« previous
next »
Pages:
[
1
]
Author
Topic: multi WAN and VLAN questions (Read 11076 times)
argie01
Jr. Member
Offline
Posts: 3
multi WAN and VLAN questions
«
on:
Friday 02 December 2011, 08:59:10 pm »
Hi,
I'm testing Endian 2.4.1 and I need some help to configure it.
I configured 3 interfaces, each one connected to a diferent VLANs. So, these are my questions:
1. Do I need to create VLANs on Endian, too? Because the VLANs I talk above are created on my main switch and on VMware, but not on Endian.
2. I configured the zones green, red, and orange. But green zone is VLAN for servers, and I don't know how to tell to Endian that to get into the user's VLAN it has to use a gateway (i.e., my main switch as gateway). So, now to admin Endian I have to get into the web from a server, and I can't do it from my PC.
3. Multi WAN: I need to configure 2 WANs. One of then (the main one), is on red zone. I'm planning to connect the other one to orange zone. I don't need to use both WAN at the same time, but I need to know how to configure orange zone as a backup WAN. And a way to switch to it, just in case...
Thank you for your help.
Logged
argie01
Jr. Member
Offline
Posts: 3
Re: multi WAN and VLAN questions
«
Reply #1 on:
Saturday 03 December 2011, 12:15:41 am »
Hi again,
meanwhile I wait for an answer to the post above I did some configuration on EF:
1. I created a green an a red zone (I deleted the orange zone).
2. On "Network/Interfaces" I created another interface that is my backup WAN line (uplink1).
3. I disabled the main interface (just for test: I connected the backup WAN router to this new FW).
4. I created two static routes:
0.0.0.0/24 WAN_main_ip/32 Main Link
0.0.0.0/24 WAN_backup_ip/24 Backup Link
Then I wrote a route on my main switch to redirect a particular public-internet-ip to Endian FW. My hope here was that I could reach that public Ip using the wan backup link.
But it doesn't works.
I don't know why. Thank you for your help.
PS: One curious thing here is despite the routes I wrote on "Network/Routes (static)" I didn't see that routes on "Status/Network Status". The routes there are always the same... and I'm not sure that is correct.
Logged
Pages:
[
1
]
« previous
next »
Jump to:
Please select a destination:
-----------------------------
Announcements
-----------------------------
=> Project News
=> Latest News and Updates
-----------------------------
Support
-----------------------------
=> General Support
=> Installation Support
=> EFW SMTP, HTTP, SIP, FTP Proxy Support
=> VPN Support
=> Hardware Support
-----------------------------
Development
-----------------------------
=> EFW Wishlist
=> Contribute Your Customisations & Modifications
Page created in 0.047 seconds with 18 queries.
Powered by SMF 1.1 RC2
|
SMF © 2001-2005, Lewis Media
Design by
7dana.com