EFW Support
Welcome,
Guest
. Please
login
or
register
.
Did you miss your
activation email?
Sunday 08 September 2024, 12:22:22 pm
1 Hour
1 Day
1 Week
1 Month
Forever
Login with username, password and session length
The Latest Endian Firewall is now available for download
HERE
14247
Posts in
4376
Topics by
6509
Members
Latest Member:
VikyV
Search:
Advanced search
EFW Support
Support
VPN Support
IPsec/NAT not working
0 Members and 5 Guests are viewing this topic.
« previous
next »
Pages:
[
1
]
Author
Topic: IPsec/NAT not working (Read 16850 times)
JEK
Jr. Member
Offline
Posts: 3
IPsec/NAT not working
«
on:
Thursday 12 October 2017, 06:32:16 pm »
Hi,
I'm running Endian Community 3.0 and I'm having trouble connecting to another net over IPsec.
Well, the tunnel is actually connecting but I'm not able to ping anything on the other side. I'm assuming that there's a problem with the NAT I configured. The nets that should be connected are 10.10.0.0/24 (my side) and 172.25.99.0/24.
I configured the following NAT rule:
Source NAT
Source: Network/IP 10.10.0.0/16
Destination: Network/IP 10.10.0.0/24
Service/Port: ANY/ANY
NAT to source address Auto
Maybe someone can point me to where I'm wrong? Help is much appreciated.
Thanks in advance.
Logged
Dark-Vex
Sr. Member
Offline
Posts: 105
Re: IPsec/NAT not working
«
Reply #1 on:
Monday 16 October 2017, 06:12:14 pm »
Hi,
why you have setup this Source NAT rule? for the IPSec tunnel is not necessary.
If you cannot reach the other side maybe the tunnel is not properly established, could you please try from SSH to run the following command in order to see if the IPSec tunnel is up?
ipsec statusall
Bye
Daniele
Logged
JEK
Jr. Member
Offline
Posts: 3
Re: IPsec/NAT not working
«
Reply #2 on:
Friday 10 November 2017, 01:26:18 am »
Hi,
I would really like to do that but I'm not sure how to connect to the system via SSH. I have credentials for the login to the web interface but these do not work for SSH.
Regards
Logged
Dark-Vex
Sr. Member
Offline
Posts: 105
Re: IPsec/NAT not working
«
Reply #3 on:
Monday 13 November 2017, 07:07:18 pm »
You can use on Windows the software Putty for connect to the firewall, the username for access to the system is "root" and the password that you have set
Logged
JEK
Jr. Member
Offline
Posts: 3
Re: IPsec/NAT not working
«
Reply #4 on:
Tuesday 14 November 2017, 07:47:06 pm »
Ok. My fault. I must have mistyped my password...
The status of the tunnel is CONNECTING. But that's just because it gets disconnected after a few hours of not using it. If someone from the other side of the tunnel is pinging something on my side the tunnel establishes and they can reach my net.
But it's not working from my side. So I was assuming it has to have something to do with my NAT.
Just to be sure it's clear what I'm trying to do. My net is 10.10.0.0/16. I'm trying to connect to the net 172.25.99.0/24 through IPSEC. I was thinking that I need to configure NAT on my side from 10.10.0.0/16 to 10.10.0.0/24 to get this working.
Regards
Logged
Pages:
[
1
]
« previous
next »
Jump to:
Please select a destination:
-----------------------------
Announcements
-----------------------------
=> Project News
=> Latest News and Updates
-----------------------------
Support
-----------------------------
=> General Support
=> Installation Support
=> EFW SMTP, HTTP, SIP, FTP Proxy Support
=> VPN Support
=> Hardware Support
-----------------------------
Development
-----------------------------
=> EFW Wishlist
=> Contribute Your Customisations & Modifications
Page created in 0.047 seconds with 20 queries.
Powered by SMF 1.1 RC2
|
SMF © 2001-2005, Lewis Media
Design by
7dana.com