Welcome, Guest. Please login or register.
Did you miss your activation email?
Friday 13 December 2024, 07:45:58 pm

Login with username, password and session length

Get the new Updates directly from Endian  HERE
14261 Posts in 4377 Topics by 6517 Members
Latest Member: Sandro
Search:     Advanced search
+  EFW Support
|-+  Support
| |-+  EFW SMTP, HTTP, SIP, FTP Proxy Support
| | |-+  2.3 Backup with 2.3 RC1 Proxy blocks everything
0 Members and 1 Guest are viewing this topic. « previous next »
Pages: [1] Go Down Print
Author Topic: 2.3 Backup with 2.3 RC1 Proxy blocks everything  (Read 19346 times)
AAAAA
Jr. Member
*
Offline Offline

Posts: 2


« on: Thursday 17 December 2009, 11:44:20 pm »

After a new installation with release 2.3 and a backup from 2.3 rc1 the proxy blocks everything. Furthermore havp is down. Thers is no chance to get the proxy running, no matter if transparent or non-transparent mode is used and no matter if whitelist/blacklist are available in /var/efw/havp/.

Solution:
Don`t backup 2.3 with 2.3 rc1. Configure everything again and the proxy works fine.

Setup:
transparent mode, port 8080, Clients are configured to use proxy wit port 8080 or use proxy-url "http://<IP-Endian-Green-Zone>/proxy.pac"
Logged
gyp_the_cat
Full Member
***
Offline Offline

Posts: 81



WWW
« Reply #1 on: Friday 18 December 2009, 09:02:36 pm »

Hi AAAA, is this something similar to:

I had the same issue with 2.2 final.   I ended up fixing it by unchecking the "Activate antivirus scan" box under CONTENT FILTER tab in HTTP proxy.  Then make sure DEFAULT POLICY tab, it says "content filter only" and is enabled for all day long.

I think this is a bug with Endian.

or

This is a Bug in HAVP service on Endian 2.2 Final,  to solve this problem you need fix two broken symbolic links: /etc/havp/whitelist and /etc/havp/blacklist

# touch /var/efw/havp/whitelist
# touch /var/efw/havp/blacklist
# chown nobody.nobody /var/efw/havp/whitelist
# chown nobody.nobody /var/efw/havp/blacklist
# reboot

After restart you can use Antivirus module, hi is working again  Wink
ps: i'm not speak english...sorry my bad english  Undecided

Or a seperate issue altogether?
Logged
AAAAA
Jr. Member
*
Offline Offline

Posts: 2


« Reply #2 on: Friday 18 December 2009, 09:43:04 pm »

Hi,
i think it's a seperate issue, because the solutions from "Ryudo" and "The EricHarris" did not solve my problem, only a completley new setup of 2.3 solved my problem.
Logged
tnol2
Jr. Member
*
Offline Offline

Posts: 6


« Reply #3 on: Monday 28 December 2009, 10:52:42 pm »

The problem persist. Two solutions posted above not work. My Endian is 2.3, configured from zero, but the http proxy block all. Any idea?
Logged
tnol2
Jr. Member
*
Offline Offline

Posts: 6


« Reply #4 on: Wednesday 30 December 2009, 02:56:35 am »

Use tcpdump on its output interface, and check with which IP you are going to the Internet when the proxy is enabled. And then create a NAT to translate this address to a valid IP on the Internet.

In my case the command I used was (without the quotes):

"tcpdump-i eth1 dst 200.154.56.80"


Then my computer I tried to access the IP 200.154.56.80 by the browser, there desconbri my IP output. And I saw that the IP, although valid, was not configured on the router. So I created a NAT for this IP, converting it to the IP that was used for direct, before the use of Proxy.
Logged
Pages: [1] Go Up Print 
« previous next »
Jump to:  

Page created in 0.078 seconds with 19 queries.
Powered by SMF 1.1 RC2 | SMF © 2001-2005, Lewis Media Design by 7dana.com