EFW Support
Welcome,
Guest
. Please
login
or
register
.
Did you miss your
activation email?
Monday 16 December 2024, 03:25:23 pm
1 Hour
1 Day
1 Week
1 Month
Forever
Login with username, password and session length
Get the new Updates directly from Endian
HERE
14261
Posts in
4377
Topics by
6517
Members
Latest Member:
Sandro
Search:
Advanced search
EFW Support
Support
Installation Support
Unable to Route from REDtoGreen Network with singlerouter solution for 2-subnets
0 Members and 2 Guests are viewing this topic.
« previous
next »
Pages:
[
1
]
Author
Topic: Unable to Route from REDtoGreen Network with singlerouter solution for 2-subnets (Read 24852 times)
vijaynaik30
Jr. Member
Offline
Posts: 1
Unable to Route from REDtoGreen Network with singlerouter solution for 2-subnets
«
on:
Saturday 12 October 2013, 07:50:47 am »
Hi,
I have recently installed Endian 2.5.2 on VMWAre set-up with 2 networks and both networks are within vmware. My setup is as below:
1. Green Network has 172.10.10.x Network with Gateway as 172.10.10.1 (This IP belongs to Endian firewall Green interface). So i am using Endian firewall as a router.
2. I have another network which uses 198.10.10.x range. I have installed one more endian router and assigned it 198.10.10.1 IP
3. To make both networks reachable to each other I had to install 2 routers i.e. 172.10.10.1 and 198.10.10.1
My question is : Can i use single Endian router and make both networks reachable ? If i put 172.10.10.1 on green then it behaves as a gateway for all 172.10.10.x machines. However for 198.10.10.x machines, i need one more router...
How can i achieve above using single Endian Router Machine for both networks ?
Thanks in advance for the help.. I am new to Endian..
Logged
jaschultzy
Jr. Member
Offline
Posts: 3
Re: Unable to Route from REDtoGreen Network with singlerouter solution for 2-subnets
«
Reply #1 on:
Sunday 20 October 2013, 02:51:54 am »
Sounds like you should only need to create a routing table on the Endian. I am a bit new myself but that's what I would try. Think it through before just throwing routes on it. I put a route of last resort on mine and locked myself out of the green network because I applied it too soon. Here's what I would try but keep in mind that I'm new here as well.
Source Destination Gateway (I think this is how Endian translates "next hop")
0.0.0.0 198.10.10.0 /24 172.10.10.2
0.0.0.0 172.10.10.0 /24 172.10.10.2
198.10.10.0 /24 0.0.0.0 default gateway of ISP
172.10.10.0 /24 0.0.0.0 default gateway of ISP
I know the routes seem weird, but I'm not sure the Endian picks up directly connected routes the same way a router would so better to be safe than sorry. I thought there was somewhere in the GUI where you could view the routing table but I cannot find it. Good luck.
Logged
Pages:
[
1
]
« previous
next »
Jump to:
Please select a destination:
-----------------------------
Announcements
-----------------------------
=> Project News
=> Latest News and Updates
-----------------------------
Support
-----------------------------
=> General Support
=> Installation Support
=> EFW SMTP, HTTP, SIP, FTP Proxy Support
=> VPN Support
=> Hardware Support
-----------------------------
Development
-----------------------------
=> EFW Wishlist
=> Contribute Your Customisations & Modifications
Page created in 0.063 seconds with 21 queries.
Powered by SMF 1.1 RC2
|
SMF © 2001-2005, Lewis Media
Design by
7dana.com