EFW Support
Welcome,
Guest
. Please
login
or
register
.
Did you miss your
activation email?
Friday 13 December 2024, 05:21:24 pm
1 Hour
1 Day
1 Week
1 Month
Forever
Login with username, password and session length
Get the new Updates directly from Endian
HERE
14261
Posts in
4377
Topics by
6517
Members
Latest Member:
Sandro
Search:
Advanced search
EFW Support
Support
Installation Support
Unable to connect to Endian's web interface after install
0 Members and 1 Guest are viewing this topic.
« previous
next »
Pages:
[
1
]
Author
Topic: Unable to connect to Endian's web interface after install (Read 21361 times)
MAllam
Full Member
Offline
Posts: 15
Unable to connect to Endian's web interface after install
«
on:
Tuesday 17 November 2009, 03:54:11 am »
Hi,
Ive just tried installing Endian on VMWare Server, the install goes ahead perfectly and I set the green IP to 10.10.254.1 but nothing else from here works, I cannot ping the IP and I cannot access the web interface for it either. I then tried doing a reinstall in VirtualBox and get the same problem, any ideas?
Im installing the new 2.3 ISO
My machine is a Dell PowerEdge 2950 1u
NIC #1 = Connected to network, IP of 10.10.254.3
NIC #2 = Connected to DSL, IP of 192.168.1.254
Ive tried swapping the two nics around, ive tried using NAT and Bridged mode within VirtualBox and none will allow me to ping or access the web interface, am I missing something obvious?
Please help
Mike
Logged
MAllam
Full Member
Offline
Posts: 15
Re: Unable to connect to Endian's web interface after install
«
Reply #1 on:
Wednesday 18 November 2009, 03:04:30 am »
No one? can anyone give me a quick setting guide for changes I need to make to get endian to run in Virtualbox? please, urgent!
Logged
MAllam
Full Member
Offline
Posts: 15
Re: Unable to connect to Endian's web interface after install
«
Reply #2 on:
Thursday 26 November 2009, 01:07:21 am »
No one? hmm ...
Logged
mrkroket
Hero Member
Offline
Posts: 495
Re: Unable to connect to Endian's web interface after install
«
Reply #3 on:
Thursday 26 November 2009, 02:06:15 am »
It seems a config problem on VMWare Server, not on Endian.
I've setup EFW 2.3 on both VMWare Server 1 and 2 and it has no problems.
On VMware check you virtual networks. If you have more than 1 NIC, you shouldn't use automatically bridged, it gives you a random NIC.
On VMWare Server, go to
Host->Virtual Network Settings->Host Virtual Network Mapping
Define VMNet2 as your first NIC, and VMNet3 as your 2nd.
Now, on your virtual machine assign VMNet2 to your first virtual NIC, and VMNet3 to your second. Check that they are connected (powered on), sometimes it appears disabled.
Double check that your GREEN IP falls on the same subnet that your first NIC.
Start pinging. If doesnt reply try to swap VMNet2 & VMNet3 on your virtual machine.
Logged
Pages:
[
1
]
« previous
next »
Jump to:
Please select a destination:
-----------------------------
Announcements
-----------------------------
=> Project News
=> Latest News and Updates
-----------------------------
Support
-----------------------------
=> General Support
=> Installation Support
=> EFW SMTP, HTTP, SIP, FTP Proxy Support
=> VPN Support
=> Hardware Support
-----------------------------
Development
-----------------------------
=> EFW Wishlist
=> Contribute Your Customisations & Modifications
Page created in 0.063 seconds with 18 queries.
Powered by SMF 1.1 RC2
|
SMF © 2001-2005, Lewis Media
Design by
7dana.com