Welcome, Guest. Please login or register.
Did you miss your activation email?
Friday 06 December 2024, 09:07:11 am

Login with username, password and session length

CLICK HERE for the The official Endian Roadmap and Issue tracker
14261 Posts in 4377 Topics by 6517 Members
Latest Member: Sandro
Search:     Advanced search
+  EFW Support
|-+  Support
| |-+  General Support
| | |-+  No access to GUI after fresh install
0 Members and 2 Guests are viewing this topic. « previous next »
Pages: [1] Go Down Print
Author Topic: No access to GUI after fresh install  (Read 18789 times)
ericmet
Jr. Member
*
Offline Offline

Posts: 4


« on: Saturday 16 June 2012, 12:36:38 pm »

Hello all, and thanks in advance for any support you can provide. I am a newb to Linux and Endian, so please forgive me in advance if I make a fool of myself. Embarrassed

I have installed Endian 2.5.1 tonight on an old Pentium 4 I had laying around, and everything seemed to go smoothly. But, after reboot, I can't seem to access the machine. I have an onboard NIC and a PCI NIC, and they're both active when I plug in a cable. I don't have a crossover cable, so what I did was connect a cable from my onboard NIC to the WAN port on my Gb switch, and a cable from my laptop to a LAN port on that switch. I have the laptop's NIC set to a static IP with the correct subnet mask and default gateway. When I try to ping the Endian machine's IP, it either times out or I get a "Destination host unreachable" message. I tried to access the GUI via a web browser, and it times out. I tried switching the cable on the Endian machine from the onboard NIC to the PCI NIC, and I get the same results. I tried connecting the laptop NIC to both NICs just to see if that worked, and it produced the same results. I checked the Endian machine's IP via ifconfig, and everything listed is correct, so I am at a loss as what to do next.

Please, if anyone can help me, I would greatly appreciate it. I searched the forums (and google) and tried everything I read that I thought could help, and nothing worked. Any ideas?  Huh
Logged
kashifmax
Sr. Member
****
Offline Offline

Gender: Female
Posts: 108


« Reply #1 on: Sunday 17 June 2012, 07:18:58 pm »

When you define IP for GREEN than it will going to allow that traffic within the GREEN network if you have defined it correctly. Secondly it may be possible that one of the NIC is doing problems for you, so try to configure with one NIC. Also try to plug the EFW's NIC to other switch port rather than WAN port...
Logged
ericmet
Jr. Member
*
Offline Offline

Posts: 4


« Reply #2 on: Monday 18 June 2012, 02:08:03 am »

Ok, so in order to configure the EFW with one NIC, should I remove the PCI NIC and reinstall? Also, during the install, should I have had to enter an IP for each NIC, because it only asked for the IP for one of them, the Green NIC? In any case, I will also try your suggestion of plugging the NIC into a different port on the switch.

Thanks for your suggestions!
Logged
Daeroth
Jr. Member
*
Offline Offline

Posts: 1


« Reply #3 on: Monday 18 June 2012, 05:43:33 pm »

Remove the second nic.  That's what was causing me problems

I was having the same problem as you.  I couldn't access the GUI no matter what I did, seemed to try everything =P

Never thought about removing my 2nd NIC until this post.

After removing the second nic and running dhclient (which obviously removed the static IP I set), I finally was able to access the GUI


I have cisco 2950 switch which a cable from router is going to, to obviously broadcast.  Then from the switch I have my main computer which I am configuring from and then of course dont forget my Endian box is also connected.

If you want technical details just in case you arent familiar with linux(I don't suggest using root on any serious linux box, just for playing around with stuff like this is fine to a degree)
After booting up your endian box after install and you are at the main prompt:

1. Hit 0 for shell
2. Type login
3. default pass is endian
4. dhclient
5. exit (your new ip will be displayed)

The IP that is going to be assigned is going to come from your dhcp server that is connected whether it be a router or a server etc.

Sorry not sure how experience you are... just tryin to help. =)
Logged
ericmet
Jr. Member
*
Offline Offline

Posts: 4


« Reply #4 on: Monday 18 June 2012, 11:09:28 pm »

Thanks for the suggestions! I will try it later this evening after work.

But, I have a question. After removing the 2nd NIC, do I just install it after I can get into the GUI to configure the EFW?
Logged
ericmet
Jr. Member
*
Offline Offline

Posts: 4


« Reply #5 on: Wednesday 20 June 2012, 11:24:20 am »

Ok, oddly enough, it was a combination of the suggestions above. I was finally able to get into the GUI  Grin

But now, I was wondering what my best options would be. Should I set the zones to DHCP or should I use static IPs? Also, in my network I have a wireless N router with 4 Gb ports and a 5 port Gb switch. Where should I place my Endian box? I was reading that I should connect the Endian box directly to my cable modem with a crossover switch with the RED zone port, and then to my LAN with the GREEN zone port. Did I read that correctly, or did I misinterpret?

Thanks in advance!
Logged
kashifmax
Sr. Member
****
Offline Offline

Gender: Female
Posts: 108


« Reply #6 on: Thursday 21 June 2012, 05:43:19 pm »

Quote
But now, I was wondering what my best options would be.
It's totally depends on your environment.

Quote
Should I set the zones to DHCP or should I use static IPs?
Use static.

Quote
Also, in my network I have a wireless N router with 4 Gb ports and a 5 port Gb switch. Where should I place my Endian box?
There are some diagrams (EFW 2.5.1). Goto Firewall > Firewall Diagram.
Router
    | (RED)
  EFW
    | (GREEN)
Clients

Quote
I was reading that I should connect the Endian box directly to my cable modem with a crossover switch with the RED zone port, and then to my LAN with the GREEN zone port. Did I read that correctly, or did I misinterpret?
Yes it's 1 of the 7 modes available in network configuration. Please read the documentation for more clarification...

http://docs.endian.com/

Logged
Pages: [1] Go Up Print 
« previous next »
Jump to:  

Page created in 0.078 seconds with 19 queries.
Powered by SMF 1.1 RC2 | SMF © 2001-2005, Lewis Media Design by 7dana.com