Welcome, Guest. Please login or register.
Did you miss your activation email?
Friday 13 December 2024, 12:12:51 pm

Login with username, password and session length

Visit the Official Endian Reference Manual  HERE
14261 Posts in 4377 Topics by 6517 Members
Latest Member: Sandro
Search:     Advanced search
+  EFW Support
|-+  Support
| |-+  Hardware Support
| | |-+  DL320 GEN8 V2 or POWEREDGE R210/R220
0 Members and 0 Guests are viewing this topic. « previous next »
Pages: [1] Go Down Print
Author Topic: DL320 GEN8 V2 or POWEREDGE R210/R220  (Read 36802 times)
mmiat
Sr. Member
****
Offline Offline

Gender: Male
Posts: 236


WWW
« on: Sunday 21 September 2014, 06:51:38 pm »

anyone knows if these server work with Endian?
thanks
Logged

---------------------
IT Consultant
www.fsw.it
Hardware & Software
mtarbox
Jr. Member
*
Offline Offline

Posts: 1


« Reply #1 on: Tuesday 23 September 2014, 11:46:14 pm »

I would imagine EFW would work fine with this setup.
Designed to run on a 32 bit architecture.
Probably also depends on how many users you plan on serving.
Logged
mmiat
Sr. Member
****
Offline Offline

Gender: Male
Posts: 236


WWW
« Reply #2 on: Wednesday 24 September 2014, 07:18:33 pm »

buyed, but it doesn't work Sad
Logged

---------------------
IT Consultant
www.fsw.it
Hardware & Software
Bloxer
Jr. Member
*
Offline Offline

Posts: 1


« Reply #3 on: Wednesday 05 November 2014, 03:45:09 am »

witch server did you  and what is not working ?
Logged
mmiat
Sr. Member
****
Offline Offline

Gender: Male
Posts: 236


WWW
« Reply #4 on: Wednesday 05 November 2014, 09:06:27 pm »

endian doesn't see newtwork interfaces of DL320
Logged

---------------------
IT Consultant
www.fsw.it
Hardware & Software
mmiat
Sr. Member
****
Offline Offline

Gender: Male
Posts: 236


WWW
« Reply #5 on: Wednesday 26 November 2014, 01:14:00 am »

I can't reply exactly what I've done, but I've installed drivers....

0) PREPARED ALL

installed from ossw repository or from updates.endian.org packages kernel-header, gcc, cpp, patch, rpmbuild, man, groff, etc.
substituted gcc3 with gcc4
in Endian 2.5.2 I've installed kernel-headers-2.6.32.43-57.e43.i586.rpm (2.5.1) and then:
ln -s /usr/src/kernels/2.6.32.43-57.e43.i586/ /usr/src/kernels/2.6.32.43-57.e48.i586

1) BROADCOM

downloaded from broadcom site: http://www.broadcom.com/support/license.php?file=570x/linux-3.136h.zip
then followed broadcom notes:
rpm -ivh tg3-<version>.src.rpm
rpmbuild -bb SPECS/tg3.spec
rpm -ivh RPMS/i386/tg3-<version>.i386.rpm
modprobe tg3

2) INTEL i350 (I've buyed hp supported network card with 2 ports)

downloaded igb-5.2.9.4.tar.gz
make install
cp /lib/modules/2.6.32.43-57.e43.i586/kernel/drivers/net/igb/igb.ko /lib/modules/2.6.32.43-57.e48.i586/kernel/drivers/net/igb/igb.ko
add "alias eth igb" in /etc/modprobe.conf
modprobe igb or insmod /lib/modules/2.6.32.43-57.e48.i586/kernel/drivers/net/igb/igb.ko
depmod -a

https://www.dropbox.com/s/um9s0f73tuylgqc/igb.ko?dl=0
https://www.dropbox.com/s/dfmzmyxcforlnso/tg3-3.136h-1.i386.rpm?dl=0
Logged

---------------------
IT Consultant
www.fsw.it
Hardware & Software
Pages: [1] Go Up Print 
« previous next »
Jump to:  

Page created in 0.094 seconds with 19 queries.
Powered by SMF 1.1 RC2 | SMF © 2001-2005, Lewis Media Design by 7dana.com