EFW Support
Welcome,
Guest
. Please
login
or
register
.
Did you miss your
activation email?
Tuesday 10 December 2024, 11:07:52 pm
1 Hour
1 Day
1 Week
1 Month
Forever
Login with username, password and session length
CLICK HERE
for the The official Endian Roadmap and Issue tracker
14261
Posts in
4377
Topics by
6517
Members
Latest Member:
Sandro
Search:
Advanced search
EFW Support
Support
Installation Support
EFW 2.4 Installation on VMWARE ESXi 3.5 fails
0 Members and 0 Guests are viewing this topic.
« previous
next »
Pages:
1
[
2
]
Author
Topic: EFW 2.4 Installation on VMWARE ESXi 3.5 fails (Read 66803 times)
arminf
Full Member
Offline
Posts: 56
Re: EFW 2.4 Installation on VMWARE ESXi 3.5 fails
«
Reply #15 on:
Wednesday 02 June 2010, 02:35:53 am »
Hi Mega
lets see your impressions after a few hours/days....
Look at the bugtracker which gets longer and even more RED!!!
I would say shame...
After 12 - 18 hours my system is unusable.. :-(
thinking on going back to 2.3...
Logged
mega
Full Member
Offline
Posts: 11
Re: EFW 2.4 Installation on VMWARE ESXi 3.5 fails
«
Reply #16 on:
Wednesday 02 June 2010, 08:22:01 am »
where can i find the bugtracker?
Logged
ESXi3.5: Supermicro /w 2x Xeon3.6, 8GB ECC, 8x Intel GB LAN, 3x RAPTOR, 1x WD 2TB GP
EFW2.4: 1000Mhz, 512MB, 8GB BusLogic, 3 NIC
necromanx
Jr. Member
Offline
Posts: 4
Re: EFW 2.4 Installation on VMWARE ESXi 3.5 fails
«
Reply #17 on:
Thursday 03 June 2010, 12:54:42 am »
Endian Issue Tracker:
bugs.endian.com
I am pretty sure you had the message about the serial connection during setup :-)
Logged
mega
Full Member
Offline
Posts: 11
Re: EFW 2.4 Installation on VMWARE ESXi 3.5 fails
«
Reply #18 on:
Thursday 03 June 2010, 01:00:51 am »
yes i didn't read carefully, there was the question t enable serial
Logged
ESXi3.5: Supermicro /w 2x Xeon3.6, 8GB ECC, 8x Intel GB LAN, 3x RAPTOR, 1x WD 2TB GP
EFW2.4: 1000Mhz, 512MB, 8GB BusLogic, 3 NIC
mxnerd
Full Member
Offline
Posts: 11
Re: EFW 2.4 Installation on VMWARE ESXi 3.5 fails
«
Reply #19 on:
Tuesday 08 June 2010, 12:13:28 pm »
What's the proper way to run Endian on VMware? I created Endian 2.4 VM on Windows VMware Server 2.02, sometimes it works and sometimes it doesn't. And somehow I can't connect to it any more.
I'm using Endian as filter only appliance so only one NIC in VM. I do bridge this VM's NIC to host's 2nd NIC, though.
Should I remove TCP/IP from host machine and leave only VMware bridge protocol?
Logged
turitopa
Full Member
Offline
Posts: 30
Re: EFW 2.4 Installation on VMWARE ESXi 3.5 fails
«
Reply #20 on:
Friday 02 July 2010, 08:08:21 am »
Hi all,
hope i am not hijacking this topic...
I had similar problems with Fresh install 2.4 onto Xenserver VM.
All started up ok, but my live logs were extremely slow to being non responsive.
I disbaled Serial port on install.
Could there be a problem with installing to XEN Vhhd? I have reverted back to 2.3 which runs smoothly on my Xenserver.
VM endian 2.3:
1GB Ram
2Vcpu
2 NIC
Logged
Running XenServr 5.5 on a Dell Poweredge 2950 III rackserver.
vm Endian 2.3
vm sbs 2008
ranger
Jr. Member
Offline
Gender:
Posts: 3
Don't drop me
Re: EFW 2.4 Installation on VMWARE ESXi 3.5 fails
«
Reply #21 on:
Monday 12 July 2010, 12:39:30 pm »
Still another hijack on the thread. - I cannot install 2.4 Respin on Virtualbox (Windows). During boot up of the installer it fails
Kernel panic - not syncing: Fatal exception in interrupt.
I have a COM port enabled on the VM
Logged
Pages:
1
[
2
]
« previous
next »
Jump to:
Please select a destination:
-----------------------------
Announcements
-----------------------------
=> Project News
=> Latest News and Updates
-----------------------------
Support
-----------------------------
=> General Support
=> Installation Support
=> EFW SMTP, HTTP, SIP, FTP Proxy Support
=> VPN Support
=> Hardware Support
-----------------------------
Development
-----------------------------
=> EFW Wishlist
=> Contribute Your Customisations & Modifications
Page created in 0.109 seconds with 18 queries.
Powered by SMF 1.1 RC2
|
SMF © 2001-2005, Lewis Media
Design by
7dana.com