[DOWNLOAD] EFW Community 3.0 + Hyper-V

[Guest]

[sota]

Hi Timmeh,

The problem only arises if I reboot from within Endian, othterwise it works fine so it's not a major issue.
I had missed the link to @50chickens post, so I may try a newer kernel with his instructions to see how it works.

Thanks,

Pat

[ppelleg]

Hello!

You can download the 7Z archived file here:


Please respond to say thank you, so I know to release updates.

Exactly what I'm looking for... no Linux experienced... :-(

Thank You a lot... and more if You may send me the password

Pino

[patochebdx]

Hello thank you for your ISO could you send me the password please...

Bye ... 

[sota]

I believe the password is timmeh or perhaps Timmeh.

[xeon_1]

thank you for providing an vhd
Currently downloading to test it

[lolotiti06]

Hi,

I have downloaded and installed your version.
This works great except one important thing. I am not able to turn on the proxy (either transparent or non-transparent)

When I turn it on, it just stops web access (transparent). When this is set to non-transparent browser states it cannot connect to the proxy.

Any idea ?

Thanks in adavance

[lolotiti06]

My configuration is extremely simple

clients --- 192.168.0.254 Endian static IP --- bridge --- internet

Hi,

I have downloaded and installed your version.
This works great except one important thing. I am not able to turn on the proxy (either transparent or non-transparent)

When I turn it on, it just stops web access (transparent). When this is set to non-transparent browser states it cannot connect to the proxy.

Any idea ?

Thanks in adavance

[swoopy]

Hi,

first of all thank you very much for your vhd. I was looking quite often for a hyper-v-solution but found nothing.
When I want to start endian, everything is working find, but endian can not find the second nic. It allways shows <eth0>.
To my maschine I added two nics for green and red. Not legacy.
Do you have a solution for that?

best reagrds

[Timmeh]

Hi,

first of all thank you very much for your vhd. I was looking quite often for a hyper-v-solution but found nothing.
When I want to start endian, everything is working find, but endian can not find the second nic. It allways shows <eth0>.
To my maschine I added two nics for green and red. Not legacy.
Do you have a solution for that?

best reagrds

Try factory reset the VHD when you have it setup... So that it re-detects your network adapters

[Timmeh]

I think this may be a bug within Endian, according to the changelog of the new version a similar issue to this is now resolved.

My configuration is extremely simple

clients --- 192.168.0.254 Endian static IP --- bridge --- internet

Hi,

I have downloaded and installed your version.
This works great except one important thing. I am not able to turn on the proxy (either transparent or non-transparent)

When I turn it on, it just stops web access (transparent). When this is set to non-transparent browser states it cannot connect to the proxy.

Any idea ?

Thanks in adavance

[chipbr]

hi everybody.

i've downloaded the VM and it works great, no more latency and ping problems because it fully support Hyper-V NICs

however, I also cannot start squid proxy. It simple don't work.
Already tried to reset factory settings twice.

Anybody got it to run? I saw a reply above stating this is a endian bug and was fixed... if so,how to upgrade the version?

[pjakpatryk]

Do anyone know a way to install it with legacy network adapters (fresh install) and than add/replace kernel with version supporting hyper-v new/regular network adapters? There is a new beta 3.0.5, I'd like to have fresh installation of it + the right kernel.

[swoopy]

Hi,

first of all thank you very much for your vhd. I was looking quite often for a hyper-v-solution but found nothing.
When I want to start endian, everything is working find, but endian can not find the second nic. It allways shows <eth0>.
To my maschine I added two nics for green and red. Not legacy.
Do you have a solution for that?

best reagrds

Try factory reset the VHD when you have it setup... So that it re-detects your network adapters

Hi,
I downloaded it again, mounted the vhd and it worked for the first time. I saw all the connected nics. But after reboot of the VM I got the same problem again. There is always one nic less than connected. Reset, reboot or migration to another hyper-v did not solve the problem. Do you have a solution?

Best regards
Christian

[philippecampos]

Dear,

I am Brazilian and not field the English language.

I could make the proxy function normally, with and without authentication in AD.

My version is the 3.0.5beta1, updated via efw-upgrade -s, but it was not what made it work.

Following procedure:

1. Repository Endian (updates.endian.org/3.0.5-beta1/pool/) downloaded the packages:

squid-3.4.9-7.endian34.i586.rpm
efw-proxy-3.0.47-2.endian17.noarch.rpm

***You can search for these files according to your version of Endian, just browse the folders repository.***

I could not download the packages directly on Endian, always I gave error first downloaded on my desktop and moved to the server using WinSCP.

2. Before it is necessary to delete a folder squid not to give error during install the new packages:

rm -rf /usr/share/squid/errors/sr *

3. I installed both using the command:

rpm -Uvh squid-3.4.9-7.endian34.i586.rpm
rpm -Uvh efw-proxy-3.0.47-2.endian17.noarch.rpm

4. Restart the Endian

5. Enable Proxy

6. Smile  

[philippecampos]

UPDATED

Dear,

I am Brazilian and not field the English language.

I could make the proxy function normally, with and without authentication in AD.

My version is the 3.0.5beta1, updated via efw-upgrade -s, but it was not what made it work.

Following procedure:

Repository Endian

*My version (updates.endian.org/3.0.5-beta1/pool/)

User: user used to upgrade the endian
Password: community

1. Repository Endian downloaded the packages:

squid-3.4.9-7.endian34.i586.rpm
efw-proxy-3.0.47-2.endian17.noarch.rpm

***You can search for these files according to your version of Endian, just browse the folders repository.***

I could not download the packages directly on Endian, always I gave error first downloaded on my desktop and moved to the server using WinSCP.

2. Before it is necessary to delete a folder squid not to give error during install the new packages:

rm -rf /usr/share/squid/errors/sr*

3. I installed both using the command:

rpm -Uvh squid-3.4.9-7.endian34.i586.rpm
rpm -Uvh efw-proxy-3.0.47-2.endian17.noarch.rpm

4. Restart the Endian

5. Enable Proxy

6. Smile