EFW Support
Welcome,
Guest
. Please
login
or
register
.
Did you miss your
activation email?
Friday 06 December 2024, 03:55:31 am
1 Hour
1 Day
1 Week
1 Month
Forever
Login with username, password and session length
CLICK HERE
for the The official Endian Roadmap and Issue tracker
14261
Posts in
4377
Topics by
6517
Members
Latest Member:
Sandro
Search:
Advanced search
EFW Support
Support
Hardware Support
Enabling SATA drive support in pre2
0 Members and 2 Guests are viewing this topic.
« previous
next »
Pages:
[
1
]
Author
Topic: Enabling SATA drive support in pre2 (Read 61871 times)
euser4life
Full Member
Offline
Posts: 13
Enabling SATA drive support in pre2
«
on:
Thursday 04 May 2006, 10:34:08 am »
Does anyone know of a way to enable sata drive support in the latest snapshot? I have a pair of SATA drives in a RAID 1 configuration that appears to load successfully but when I reboot I receive a kernel panic message "failed to sync". Any help would be appreciated.
Thanks,
Euser4life
Logged
finchwizard
Guest
Re: Enabling SATA drive support in pre2
«
Reply #1 on:
Friday 05 May 2006, 10:05:50 am »
SATA Support was not compiled into the PreRelease because they did not have a SATA machine to test it on.
SATA support has been enabled and will be available until the Final Release v2.
You may need to run RC8 or one of the older versions, I think they support SATA from memory.
Logged
euser4life
Full Member
Offline
Posts: 13
Re: Enabling SATA drive support in pre2
«
Reply #2 on:
Friday 05 May 2006, 11:59:27 am »
Yeah I tried to run RC8 and on setup I get a message stating that it fails to bring up the network interface. (Broadcom gigbit nics). Pre2 does not have this problem and finishes setup but gives me the kernel panic on reboot because of no sata support.... Looks like I'm darned if I do and darned if I don't.
Logged
finchwizard
Guest
Re: Enabling SATA drive support in pre2
«
Reply #3 on:
Monday 08 May 2006, 08:26:17 am »
I remember using a Broadcom on RC8 in one of my servers and it seemed to work ok.
Do you have the exact message? It may be easier to fix that than doing a kernel recompile
Logged
euser4life
Full Member
Offline
Posts: 13
Re: Enabling SATA drive support in pre2
«
Reply #4 on:
Tuesday 09 May 2006, 02:40:06 am »
Well I get through the setup to input Endian's ip and netmask and when I click "ok" I get a message stating "Interfaced Failed to Come Up" and when I "alt F3" it states:
SIOCSIFADDR: No such device
SIOCSIFNETMASK: No such device
SIOCSIFFLAGS: No such device
Any help is appreciated...
Logged
finchwizard
Guest
Re: Enabling SATA drive support in pre2
«
Reply #5 on:
Tuesday 09 May 2006, 07:57:04 am »
And it is enabled in BIOS etc.
Also check to see if 'ifconfig' says anything.
Try running 'lsmod' to see what Modules are also loaded, see if the Ethernet one is loaded.
Logged
Pages:
[
1
]
« previous
next »
Jump to:
Please select a destination:
-----------------------------
Announcements
-----------------------------
=> Project News
=> Latest News and Updates
-----------------------------
Support
-----------------------------
=> General Support
=> Installation Support
=> EFW SMTP, HTTP, SIP, FTP Proxy Support
=> VPN Support
=> Hardware Support
-----------------------------
Development
-----------------------------
=> EFW Wishlist
=> Contribute Your Customisations & Modifications
Page created in 0.078 seconds with 18 queries.
Powered by SMF 1.1 RC2
|
SMF © 2001-2005, Lewis Media
Design by
7dana.com