Ok...I edited /etc/ssh/sshd_conf.tmpl and changed the settings there.  That did the trick.

HL

Hi all,

Recently installed Endian Community edition (upgraded to 3.3.19).  I noticed that the ssh configuration reverts to the default after a reboot.  For example, I usually edit /etc/ssh/sshd.conf to make certain changes (e.g. AllowUsers <myuser only>. Port 2222, PasswordAuthentication no).  Whenever the server reboots, it reverts to the default values (Port 22, AllowUsers root support and PasswordAuthentication yes).  How can I preserve my changes across reboots?

Thanks in advance.
Hilkiah

hello,

is there a way to install development tools on endian firwall?
i'm tryinbg to make igmp proxy to work and i think compiling its the only way.

thanks

Hello everyone,

I had a problem for a while that I can't solve, the configuration of my Endian router/firewall is as follows: 4 network cards, 1 X Eolo antenna input line, 1 x Gbit wired network green line, 1 x WiFi Gbit blue line , 1 x Wired Red Line x DMZ (which I don't use).

Now the problem is as follows on the wired green line I have a Synology server that I would like to reach from clients that are on the blue WiFi line, I routed the firewall from the server's IP address to the clients creating an interzone connection.

But the file folders that are on the server I can not reach them, the files are multimedia, mostly  that are published in broadcast.

If instead the clients are on the same wired network I can see the folders and files contained within.

Tengo un Endian Firewall, versión 3.3.2

Necesito hacer una configuración muy concreta y no se como hacerla.

Tengo un nombre de con No-IP y redireccionado en el Endian un puerto a mi servidor interno, este nombre No-ip, es la dirección externa WAN del Endian.

Si desde fuera de la red del Endian pongo en un navegador el nombre No-IP : el puerto puedo acceder correctamente a mi servidor, ejemplo https:\\"nombre no-ip":8283 funciona ok.

Pero si dentro de la red, donde está trabajando el Endian, escribo ese mimo ejemplo de antes, los navegadores no me abren la web del servidor.

Si por el contrario escribo https:\\" dirección IP de la red interna":8283 si puedo acceder correctamente, ejemplo https:\\192.168.0.174:8283 esto si me funciona, pero no es lo que necesito.

Lo que necesito es configurar el Endian y no se como hacerlo, para que desde la red interna(192.168.0.0) poniendo el nombre No-IP:8283 me consiga abrir el servidor.

Gracias, espero me ayuden.

Hi,

I have the following setup in a Hyper-V:

EFW 3.3.15 = Public IP
EFW 3.3.15 LAN = 192.168.110.1 (DHCP 192.168.110.0/24)
RRAS LAN = 192.168.110.15
RRAS VPN Server = 192.168.120.1 (Static Pool 192.168.120.0/24)
VPN Client = 192.168.120.2

I cannot reach the 192.168.110.0/24 network once i connect via VPN (i can get to the RRAS & Internet and that's it). I searched in many places, enabled Promiscuous mode on the Internal vSwitch, Disabled BADTCP drop in EFW, added a static route in EFW so it will know to send comms for 192.168.120.0/24 to 192.168.110.15 (via web interface and also ssh). Maybe I'm not putting it where it should be via SSH, my Linux knowledge is severely lacking, so trial & error was the way so far, but I'm about to give up on this. I've got to the point where I'm putting routes in VPNClient/RRAS/EFW that don't make sense even to me, just to see if anything changes.

If anyone has the knowledge and patience to explain in an idiot-proof way how such a setup should be configured i would be in his/her .

Thanks.

Hi, does it also happen to you that the firewall restarts several times even in one day for no reason? It's not an electrical problem. Could it be because of a link that is often offline?

Endian version 3.3.16, 3.3.17, 3.3.19.

Hi I am running EF 3.3.2 in my Dashboard under Updates I am showing
"Updates on this system have been activated successfully."

I think its the current version though out of curiosity tried a efw-upgrade (In the shell prompt) and sure enough it didn't find any new packages though does give the error
error: Failed acquiring release file for 'efw-community':
error: h t t p://(MY CORRECT %40 EMAIL):community@updates.endian.org/3.2/repodata/repomd.xml: [Errno -2] Name or service not known

Is this normal? Thanks.

Why is Endian Firewall restricting my bandwidth? the network card configured in the red zone has a static (public) ip, the other green network card is configured to my LAN network, the data download speed in the red zone card is 30mb, in the green zone the speed download is 5mb could you help me please

Hello,
on my endian i configured OpenVPN server and 2 IpSec VPn with 2 remote sites.
My question is if it is possible to make users connected on openvpn reach remote ipsec networks.
Thank you.