|
Title: nVidia Corporation MCP78S [GeForce 8200] Ethernet Post by: agvieyra on Monday 28 September 2009, 11:28:20 am Hi guys.
I'm new to Endian, but I've already installed it two times before, and everything worked fine. But, now I need to configure a machine with 4 NIC cards, so I bought a new Mother. This board come with an integrated NIC. Endian doesn't recognize the chip-set, nor the card. So, now I'm in that machine a with a live UBUNTU, and everything works fine, so I give the info to see if anyone can help me: OS: I tried Endian 2.2 and 2.3 RC1 (none works) endian firewall From UBUNTU: ubuntu@ubuntu:~$ lspci -v 00:00.0 RAM memory: nVidia Corporation MCP78S [GeForce 8200] Memory Controller (rev a2) Subsystem: ASUSTeK Computer Inc. Device 82f2 Flags: bus master, 66MHz, fast devsel, latency 0 Capabilities: [94] HyperTransport: #1a Capabilities: [60] HyperTransport: Retry Mode ........ ....... (Very large list, and a lot of Nvidia Corporation MCP78S Devices) ....... And finally ...... 00:0a.0 Ethernet controller: nVidia Corporation MCP78S [GeForce 8200] Ethernet (rev a2) Subsystem: ASUSTeK Computer Inc. Device 82f2 Flags: bus master, 66MHz, fast devsel, latency 0, IRQ 2299 Memory at f7e7c000 (32-bit, non-prefetchable) [size=4K] I/O ports at b880 Memory at f7e7f400 (32-bit, non-prefetchable) [size=256] Memory at f7e7f000 (32-bit, non-prefetchable) [size=16] Capabilities: [44] Power Management version 2 Capabilities: [50] Message Signalled Interrupts: Mask+ 64bit+ Queue=0/4 Enable+ Capabilities: [6c] HyperTransport: MSI Mapping Enable+ Fixed+ Kernel driver in use: forcedeth Kernel modules: forcedeth ......... List continue ........ (and my other card (works fine in both OSes (a Classic...) 01:07.0 Ethernet controller: 3Com Corporation 3c905C-TX/TX-M [Tornado] (rev 78) Subsystem: 3Com Corporation Device 1000 Flags: bus master, medium devsel, latency 64, IRQ 16 I/O ports at dc00 [size=128] Memory at f7fffc00 (32-bit, non-prefetchable) [size=128] Expansion ROM at 88000000 [disabled] [size=128K] Capabilities: [dc] Power Management version 2 Kernel driver in use: 3c59x Kernel modules: 3c59x ...... (list continues to the end) .... So I think that the Module I need to use is 'forcedeth' But no WAY. I tried in Endian: #modprobe -v forcedeth And nothing. Ah.... Another info, from UBUNTU: ubuntu@ubuntu:~$ cat /proc/modules binfmt_misc 16776 1 - Live 0xf7cee000 lp 17156 0 - Live 0xf7c72000 bridge 56340 0 - Live 0xf7d97000 stp 10500 1 bridge, Live 0xf7d18000 bnep 20224 2 - Live 0xf7c59000 video 25360 0 - Live 0xf7d8e000 output 11008 1 video, Live 0xf7d7b000 input_polldev 11912 0 - Live 0xf7d5d000 ppdev 15620 0 - Live 0xf7d2d000 k8temp 12416 0 - Live 0xf7d1f000 pcspkr 10496 0 - Live 0xf7d13000 parport_pc 40100 1 - Live 0xf7d07000 parport 42220 3 lp,ppdev,parport_pc, Live 0xf7cd9000 squashfs 46344 1 - Live 0xf80f3000 aufs 165924 1 - Live 0xf7e59000 exportfs 12544 1 aufs, Live 0xf7e0b000 nls_cp437 13696 1 - Live 0xf7dff000 isofs 39844 1 - Live 0xf7dbc000 usbhid 42336 0 - Live 0xf7ccc000 forcedeth 61712 0 - Live 0xf7ca9000 3c59x 49192 0 - Live 0xf7cbd000 mii 13312 1 3c59x, Live 0xf7ca3000 fbcon 46112 0 - Live 0xf7c8c000 tileblit 10752 1 fbcon, Live 0xf7c78000 font 16384 1 fbcon, Live 0xf7c6c000 bitblit 13824 1 fbcon, Live 0xf7c5f000 softcursor 9984 1 bitblit, Live 0xf7c54000 If Anyone can help me I will be very grateful. Thanks in advance. Aguxx |