* Home Help Login Register

Welcome, Guest. Please login or register.
Did you miss your activation email?
Sunday 24 November 2024, 03:22:38 pm

Login with username, password and session length

Visit the Official Endian Bug tracker  HERE
14261 Posts in 4377 Topics by 6517 Members
Latest Member: Sandro
Search:     Advanced search
+  EFW Support
|-+  Support
| |-+  Installation Support
| | |-+  EFW 2.4 Installation on VMWARE ESXi 3.5 fails		 0 Members and 0 Guests are viewing this topic. « previous next »
Pages: 1 [2] Go Down Print
Author Topic: EFW 2.4 Installation on VMWARE ESXi 3.5 fails  (Read 61926 times)
arminf
Full Member
***
Offline Offline

Posts: 56
« Reply #15 on: Wednesday 02 June 2010, 02:35:53 am »
Hi Mega

lets see your impressions after a few hours/days....

Look at the bugtracker which gets longer and even more RED!!!
I would say shame...

After 12 - 18 hours my system is unusable.. :-(

thinking on going back to 2.3...
Logged
mega
Full Member
***
Offline Offline

Posts: 11
« Reply #16 on: Wednesday 02 June 2010, 08:22:01 am »
where can i find the bugtracker?
Logged
ESXi3.5: Supermicro /w 2x Xeon3.6, 8GB ECC, 8x Intel GB LAN, 3x  RAPTOR, 1x WD 2TB GP
EFW2.4: 1000Mhz, 512MB, 8GB BusLogic, 3 NIC
necromanx
Jr. Member
*
Offline Offline

Posts: 4
« Reply #17 on: Thursday 03 June 2010, 12:54:42 am »
Endian Issue Tracker:
bugs.endian.com

I am pretty sure you had the message about the serial connection during setup :-)
Logged
mega
Full Member
***
Offline Offline

Posts: 11
« Reply #18 on: Thursday 03 June 2010, 01:00:51 am »
yes i didn't read carefully, there was the question t enable serial
Logged
ESXi3.5: Supermicro /w 2x Xeon3.6, 8GB ECC, 8x Intel GB LAN, 3x  RAPTOR, 1x WD 2TB GP
EFW2.4: 1000Mhz, 512MB, 8GB BusLogic, 3 NIC
mxnerd
Full Member
***
Offline Offline

Posts: 11
« Reply #19 on: Tuesday 08 June 2010, 12:13:28 pm »
What's the proper way to run Endian on VMware?  I created Endian 2.4 VM on Windows VMware Server 2.02, sometimes it works and sometimes it doesn't.   And somehow I can't connect to it any more.

I'm using Endian as filter only appliance so only one NIC in VM.  I do bridge this VM's NIC to host's 2nd NIC, though. 

Should I remove TCP/IP from host machine and leave only VMware bridge protocol?
Logged
turitopa
Full Member
***
Offline Offline

Posts: 30
« Reply #20 on: Friday 02 July 2010, 08:08:21 am »
Hi all,

hope i am not hijacking this topic...
I had similar problems with Fresh install 2.4 onto Xenserver VM.
All started up ok, but my live logs were extremely slow to being non responsive.
I disbaled Serial port on install.

Could there be a problem with installing to XEN Vhhd?  I have reverted back to 2.3 which runs smoothly on my Xenserver. 
VM endian 2.3:
1GB Ram
2Vcpu
2 NIC
Logged
Running XenServr 5.5 on a Dell Poweredge 2950 III rackserver.
vm Endian 2.3
vm sbs 2008
ranger
Jr. Member
*
Offline Offline

Gender: Male
Posts: 3

Don't drop me
« Reply #21 on: Monday 12 July 2010, 12:39:30 pm »
Still another hijack on the thread.   - I cannot install 2.4 Respin on Virtualbox (Windows).  During boot up of the installer it fails

Kernel panic - not syncing: Fatal exception in interrupt.

I have a COM port enabled on the VM
Logged
Pages: 1 [2] Go Up Print 
« previous next »
Jump to:  

Page created in 0.109 seconds with 19 queries.
Powered by SMF 1.1 RC2 | SMF © 2001-2005, Lewis Media Design by 7dana.com