EFW Support

Support => General Support => Topic started by: jcaporina on Thursday 09 July 2009, 01:13:24 am



Title: New EFW 2.2 3rd NIC interface for WAN failover does not work.
Post by: jcaporina on Thursday 09 July 2009, 01:13:24 am
I have a 1U Cybortronics server with built in dual NICs, I added a 3rd NIC for WAN failover. Installed EFW 2.2 Community OS and successfully tested  Green LAN internet and  both Red WAN ports at my office , but when I connect the EFW on site with Comcast as WAN1 and Cbeyond as WAN2 and disconnect WAN1 it never fails over to WAN2. Has anyone have a problem with a simular scenario and may be able to offer a solution?


Title: Re: New EFW 2.2 3rd NIC interface for WAN failover does not work.
Post by: necomputer on Sunday 12 July 2009, 09:24:43 am
I haven't worked with Endian for very long but I am rapidly expanding my knowledge of the system because our company has become a reseller in the US. My initial reaction from having configured sonicwalls and cisco equipment is that the problem is coming with your configuration of the wan to lan interface. You need to reference a connection that represents the WAN interfaces and then make both WANs reside under that connection. This way when one connection fails a last resort will kick the connection over to WAN2.

I know this isn't the best as far as specifics but I will follow up with more information once I duplicate the same setup (which I need to do anyways).


Title: Re: New EFW 2.2 3rd NIC interface for WAN failover does not work.
Post by: sp_kimji on Monday 13 July 2009, 06:38:55 pm
I will confirm EFW2.2 Stable Release can use fail-over.
Because, now I use 1PC with 3 NIC (1NIC for Green and 2NIC for RED) and config it for fail-over.
When I try to down WAN1 and wait about not over 5 minute. Routing is switch to WAN2 automatically.
And when WAN1 is up, routing is switch to WAN1 again (automatically).

If you can't use fail-over. Checking your config again.
see the example picture and try to config again (this picture show config of WAN2 for backup)
You must config this in WAN1 too.

Goodluck!   ;D


Example Picture

(http://lh4.ggpht.com/_yBwN635MjLw/SM4bitBb8wI/AAAAAAAACZ4/eeW8VFA7LVM/s576/endian_loadbalance.png)


Title: Re: New EFW 2.2 3rd NIC interface for WAN failover does not work.
Post by: mrkroket on Wednesday 15 July 2009, 08:02:55 am
En network->Interfaces double check these options:

-" if this uplink fails activate :" Enabled, check the connectivity of the 2nd WAN
-"Check if these hosts are reachable": Enable it and put your WAN gateway and some inet hosts: i.e www.google.com. This way if pings fail the firewall will failover to the 2nd WAN.



Title: Re: New EFW 2.2 3rd NIC interface for WAN failover does not work.
Post by: hezina on Wednesday 15 July 2009, 09:57:33 pm
Hi,

i have same truble but only with 1 RED interface... my RED interface connection on Provider ... link state is OK... but MAC address for DefaultGateway is "Incomplet"!!!

if I connect on same cable user notebook with MS Windows XP all OK  .. and arp table have corect HW Address ...

anybody have any idea???

Many thanks

Petr


Title: Re: New EFW 2.2 3rd NIC interface for WAN failover does not work.
Post by: haiau on Monday 28 September 2009, 07:19:49 pm
I will confirm EFW2.2 Stable Release can use fail-over.
Because, now I use 1PC with 3 NIC (1NIC for Green and 2NIC for RED) and config it for fail-over.
When I try to down WAN1 and wait about not over 5 minute. Routing is switch to WAN2 automatically.
And when WAN1 is up, routing is switch to WAN1 again (automatically).

If you can't use fail-over. Checking your config again.
see the example picture and try to config again (this picture show config of WAN2 for backup)
You must config this in WAN1 too.

Goodluck!   ;D


Example Picture

(http://lh4.ggpht.com/_yBwN635MjLw/SM4bitBb8wI/AAAAAAAACZ4/eeW8VFA7LVM/s576/endian_loadbalance.png)


I installed EFW completely new versions 2.2 and 2.3RC1, set up like your illustrations, but failover feature does not work.

http://efwsupport.com/index.php?topic=909.msg2010;topicseen#msg2010